Controlling servo with pic16f1789 for car backseat table

By

This post is about use of servo motor in Car backseat tray system.

 Servo motor :

                                    Servo motor is a dc motor with a derive circuit and position sensor for precise movements. position sensor used in servo motor is normally potentiometer attached to gears of motor.
Derive circuit typically consists of 
  1. pulse width modulation to voltage converter
  2. feedback from potentiometer
  3. supply voltages
Feedback from position sensor is compared with converted voltage and resulted output is used to correct position of motor until both signals are equal. Servo motor will maintain its position and resist  to any external change as long as modulated pulse is present at control wire of motor.

Control signal :

                              control signal is most complex signal out of three signal required to operate DC Servo motor . Other two signals are 0 v and 5 volts out of battery. To generate control signal we are using Pic 16f1789 micro-controller in pwm (pulse width modulation ) mode.

Setting Pic 16f1789 in PWM mode :

                                                                      To configure micro-controller in pwm mode first we have to configure oscillator of  Pic 16f1789 up-to our requirements . configure oscillator to 125 KHz internal oscillator. configure device for pwm mode and interrupt on change mode. Load values of wave's period and duty cycle in pr2 and corresponding CCPRxL  registers . 

Motor used :

                         Motor used in this project is dc servo motor having rotation 0-90 degrees. 1 ms pulse for minimum rotation and 2 ms pulse for full rotation operating at 50 Hz .

Code for Controlling Servo using Pic 16f1789 :

This code is written to operate servo motor according to open/close position of control button of Car backseat tray system . you can use code under the main heading if only fixed pulse is required
  #include "p16F1789.inc"
; __config 0x2FE4
 __CONFIG _CONFIG1, _FOSC_INTOSC & _WDTE_OFF & _PWRTE_OFF & _MCLRE_ON & _CP_OFF & _CPD_OFF & _BOREN_ON & _CLKOUTEN_OFF & _IESO_ON & _FCMEN_ON
; CONFIG2
; __config 0x3EFF
 __CONFIG _CONFIG2, _WRT_OFF & _PLLEN_OFF & _STVREN_ON & _BORV_LO & _LPBOR_OFF & _LVP_ON
  ORG 000H
  GOTO MAIN
  ORG 004H
  GOTO INTERRUPT_SELECT
  ORG 020H
INTERRUPT_SELECT
  BTFSS INTCON,IOCIF
  RETFIE
  BANKSEL INLVLA
  BTFSC IOCAF,0
  GOTO OPEN_CLOSE
  NOP
  RETFIE
OPEN_CLOSE
  BANKSEL PORTA
  BTFSC PORTA,0
  GOTO OPEN
  BTFSS PORTA,0
  GOTO DEFAULT
  RETURN
OPEN
  BANKSEL ODCONA
  BCF CCP1CON,DC1B1
  BCF CCP1CON,DC1B0
  MOVLW B'00000100'
  MOVWF CCPR1L
  BANKSEL INLVLA
  BCF IOCAF,0
  RETFIE
DEFAULT
  BANKSEL ODCONA
  BCF CCP1CON,DC1B1
  BCF CCP1CON,DC1B0
  MOVLW B'00000010'
  MOVWF CCPR1L
  BANKSEL INLVLA
  BCF IOCAF,0
  RETFIE

MAIN
  BSF INTCON,GIE
  BSF INTCON,PEIE
  BSF INTCON,IOCIE
  BANKSEL ANSELA
  BCF ANSELA,0
  BANKSEL INLVLA
  BSF IOCAP,0
  BSF IOCAN,0
  BANKSEL TRISA
  BSF TRISA,0
  MOVLW B'00101000'
  MOVWF OSCCON
  CLRF OSCTUNE
  BSF TRISC,2
  BANKSEL ODCONA
  MOVLW B'00001100'
  MOVWF CCP1CON
  MOVLW B'00000010'
  MOVWF CCPR1L
  BANKSEL PORTA
  MOVLW .38
  MOVWF PR2   
  MOVLW B'00000110'
  MOVWF T2CON
  BANKSEL TRISA
  BCF TRISC,2
  BANKSEL INLVLA
  BCF IOCAF,0
HERE
  GOTO HERE
  END
  







Comments

Post a Comment

Popular posts from this blog

Car backseat table

By
Having your lunch or a light meal while you are travelling is a trouble for every one. Some of luxurious cars are now including tables for passengers on backseats. One approach to have this facility is to design your own using simple steps and parts 1st of all you need to make table top for which you can use kitchen cutting board as table top or you can machine your own . Modify it upto your requirements like cup holding place etc Next you have to plan attachement to the seats. It depends on the type of seats you have. Here i can write some of possibillities like if car seats have cloth on back then you have to open cover and attach rods horizontally to the frame of seat and if seats came with plastic on back then system's base could be attached with screws directly. base will also provide mechanichal support. Next step is to dicide about working of system. Some of options are Manual. Single table operating with button. Centralized system controlled by one keypad or remote...
Read more

Car Backseat Table System using PIC Micro-controller

By
Image
Before installing micro controller to operate car backseat table read previous posts about how to install mechanical parts, installing dc motor and position sensors First of all select any  micro-controller   which is available and have external interrupts. I am using PIC-16f1789 in car backseat tray table Identify signals to operate the system To operate Car back seat table using micro-controller we need 3 signals for each table. One signal from open and close command to each table Detect open position of each table Detect close position of each table Here we are operating two tables so we need total six signals which are connected to port A through current limiting resistors(value of which depends on device type, specified on datasheet of I.C. you  are using). Electrical specifications for PIC 16f1789 Port A is used for interrupt input.Connections will be as follows. port A,1 connect with open/close button for table 1. port A,2 connect with...
Read more

Car backseat tray table mechanical assembly

By
Image
To use these pictures first read previous post and refer below pictures to assemble car seat table. car seat frame once you open leather cover of seat you will find this kind of metal strips or metal rods . you will add two rods or one sheet to give tray system mechanical support as given below mechanical support for base Attach two rods as in above diagram. you can use metal strips or a metal sheet between frame to provide mechanical support to base of car seat tray base of car back seat table Next step is to attach base. To do this drill four holes in previously attached rods making a square . reapply leather cover and drill four holes in the base of car tray base both should in front of each other joints of car seat tray table Then drill small holes keeping in mind that upper two should outwards from center and lower two should inwards and then insert four small cylinders which will act as joints(axis of rotation) for top of table tray system inserti...
Read more