Car Backseat Automatic Table

By

Before reading about automatic tray table refer to previous posts about how to install manual car backseat tray table  .
to install automatic operating system first install a rod across strips like in image
rod for rotation
Next step is selection of motor here we are using dc motor with gears to reduce speed and increase torque of motor . For installation of motor make a square like hole in the base of car tray table such that half motor fits inside that space or such that motor do not touch the top of table when fully closed.

Now attach motor to the base by drilling holes in the slot and then rotate a metal or plastic strip around motor and insert pins between metal strips and base so that motor can rotate .

Then attach a rod with threads to the shaft of motor .

Its time to insert  connect motor and system. to do so take a metal square of size just to fit two rods inside at each side drill two holes like one at left to right at the top edge of side and the other from front to back at the lower edge . make threads in one hole so rod attach to motor can rotate inside 

All parts will be connected as given in image .
final form of car tray table
Now attach two click switches to the base of car tray table to read position of table top.
As shown
switches are installed in upper right corner
Final form of car tray table will look like this
design of car backseat lunch table
final results
This will be final form of car table tray system ,
Next post is about schematic .


Comments

Post a Comment

Popular posts from this blog

Car Backseat Table System using PIC Micro-controller

By
Image
Before installing micro controller to operate car backseat table read previous posts about how to install mechanical parts, installing dc motor and position sensors First of all select any  micro-controller   which is available and have external interrupts. I am using PIC-16f1789 in car backseat tray table Identify signals to operate the system To operate Car back seat table using micro-controller we need 3 signals for each table. One signal from open and close command to each table Detect open position of each table Detect close position of each table Here we are operating two tables so we need total six signals which are connected to port A through current limiting resistors(value of which depends on device type, specified on datasheet of I.C. you  are using). Electrical specifications for PIC 16f1789 Port A is used for interrupt input.Connections will be as follows. port A,1 connect with open/close button for table 1. port A,2 connect with open/close button
Read more

Car backseat tray table mechanical assembly

By
Image
To use these pictures first read previous post and refer below pictures to assemble car seat table. car seat frame once you open leather cover of seat you will find this kind of metal strips or metal rods . you will add two rods or one sheet to give tray system mechanical support as given below mechanical support for base Attach two rods as in above diagram. you can use metal strips or a metal sheet between frame to provide mechanical support to base of car seat tray base of car back seat table Next step is to attach base. To do this drill four holes in previously attached rods making a square . reapply leather cover and drill four holes in the base of car tray base both should in front of each other joints of car seat tray table Then drill small holes keeping in mind that upper two should outwards from center and lower two should inwards and then insert four small cylinders which will act as joints(axis of rotation) for top of table tray system inserti
Read more

Controlling servo with pic16f1789 for car backseat table

By
This post is about use of servo motor in Car backseat tray system.  Servo motor :                                     Servo motor is a dc motor with a derive circuit and position sensor for precise movements. position sensor used in servo motor is normally potentiometer attached to gears of motor. Derive circuit typically consists of  pulse width modulation to voltage converter feedback from potentiometer supply voltages Feedback from position sensor is compared with converted voltage and resulted output is used to correct position of motor until both signals are equal. Servo motor will maintain its position and resist  to any external change as long as modulated pulse is present at control wire of motor. Control signal :                               control signal is most complex signal out of three signal required to operate DC Servo motor . Other two signals are 0 v and 5 volts out of battery. To generate control signal we are using Pic 16f1789 micro-controller
Read more